With +10 years of experience you can be 100% sure that you are in good hands.
We collaborate with the biggest product suppliers on the market assuring you that you get the best product and services to suit your needs and giving you the best value for the money complemented with an excellent customer service.
We are P.A.S
“Experience you can trust”
Electric Gate Options
The most popular electric gates for industrial properties are sliding gates, but these are not the only option available.
Articulated gate openers can be used for gates with wide posts allowing opening in small spaces. An easy system for installers as they are simple to install but not as aesthetically pleasing as other motor designs. Also known as Crank arm operators, they are the main type of automation system sold in Uk, where low aluminium gates are often used.
Under-gate Jack operators usually control the gate by directly moving the pivot point of each gate leaf. This makes the unit ideal cosmetically and also allows for up to 180 degrees of leaf swing as required. However controlling the pivot point of the gate, is like opening a door by twisting the hinge, and as so is very difficult due to the loads needed at that point. This is highlighted with snap, as the gate has to change direct, as soon as it can. For this reason they are recommend as only suitable for ‘Domestic’ systems in a low risk of abuse environment. Another major consideration with the use of under-gate units is that of water immersion/ingress and warranty voidance. If the water table is high or the drainage of the unit’s foundation box inadequate throughout the systems life, then water ingress and unit failure is increased.Ram or link arm units are usually simpler to install and maintain, they are visible to otherwise ignorant abuse and as they fix down along each gate leaf, they also have an obvious and sometimes major, mechanical advantage over Jacks. Therefore, Rams are far more suitable on Multi-user & commercial systems. Also the manual release is always above ground, making it often more user friendly in operation.
If space is an issue or the driveway behind the gates is on a steep incline, a better option would be a sliding gate. Sliding gates are also very popular in a industrial environment. Sliding gates are also used for cantillever gate systems.
The Electric Gate Motor
The backbone of any electric gate, whether automatic or not, is the electric gate motor, two distinct motor types exist hydraulic, or electromechanical. This is the electric device which actually enables the electric gate to open and close without having to manually push the gate. All types of electric gates and barriers make use of a motor of some kind. There are many different kinds of electric gate motors offered by a number of automation companies.
Electric Gate Safety
The safety of an automated gate is an important consideration, in the European Union, automated gate safety is specified by a series of European Normalisations. An automated gate that has not been fitted with safety in mind can potentially become a major hazard particularly to untrained users. Various safety devices are available to make sure that your gates meet the highest of European or American safety standards.
Gate and Security
Electric gates alone, however solid and imposing they may be, cannot guarantee a completely secure environment electric locks, are often needed to boost the locking effectiveness of the gate motors. Electric gates are recommended to be used in combination with other security features to install a full security system. A few of these features are closed circuits with security cameras, additional gates in conjunction with the main gate, electronic keycards and keypads, security guards.Aside from the additional security features that should go with parking barrier gates, electric security gates often offer safety features like sensors that determine when there is an obstruction to prevent the electronic gate from swinging into a vehicle or closing on somebody's hands. To prevent the electronic gates from being damaged by irresponsible drivers driving fast speed bumps are also commonly placed before gate entrances to slow down vehicles.
Safety Regulations in Europe
All installations must meet with the Machinery directive 2006/42/EC with EN13241-1 being the regulations concerning gates. The installer of the gate is responsible for the conformity to regulation, not the manufacturer. The two main EN regulations that then apply are EN 12453 which describes the safety levels that should be observed when installing a gate and EN12445 which describes the testing method that must be undertaken. The major points are the maximum amount of force at certain test points. Example - a maximum of 400N of force can be applied in the last 50, 300 and 500 mm of travel of a gate, after the initial impact the force must drop to 150N within 0.75 of a second and reduce to 25N within 5 seconds. During the mid travel of a gate the allowable force is 1400N. A full risk assessment of the gates must take place with all crush, cutting points shown to the client with appropriate protection devices offered, a recommended maintenance program should also be provided. Finally the installer must confirm that all electrical equipment fitted has the European CE mark all the time.To conform to these regulations the gate system must be checked with a calibrated force tester and the full results kept in a technical file for 7 years. If the gate is not tested it does not comply. Most gate kits can be fitted with safety equipment so that these limits are achieved and so cover that part of EN13241-1.Two recent incidents in the UK when children were killed by sliding gates have resulted in the UK Health and Safety department issuing a Gate Safety Bulletin.
We also offer repairs for:
Roller shutters doors, sectional doors, high speed doors, dock levellers, electric gate, car park automatic barriers , security doors, fire doors, sliding doors, , dock bumpers, dock buffers, parking control, dock shelters, dock seals, trailer plates, wheel guides, vehicle restraint, windows, internal doors, awnings systems, canopy roofs, garage doors, loading bay equipment, pallet racking, shelving, racking protection, safety barrier systems, emergency doors, strip curtains, corner protection, kerbs, front doors, smoking shelters, and much more. Get in touch with us.
INDUSTRIAL | COMMERCIAL | DOMESTIC
Supply | Installation | Service | Repair
Roller Shutters Doors | Sectional Doors | High Speed Doors | Dock Levellers | Electric Gate | Car Park Barriers | Security Doors | Fire Doors | Sliding Doors | Bollards | Vehicle Restraint Systems | Windows Bars | Internal Doors | Awnings Systems | Canopy Roofs | Garage Doors | Loading Bay Equipment | Pallet Racking | Shelving | Racking Protection | Cable Protectors | Hose Ramps | Dock Bumpers | Dock Lights | Parking Control | Safety Signs | Dock Shelters | Dock Seals | Trailer Plates | Wheel Guides | Safety Barrier Systems | Emergency Doors | Strip Curtains | Corner Protection | Kerbs | Front Doors | Bike Racks | Smoking Shelters | Building Services
Pro Access Service 2018 Copyright @ All Rights Reserved
Pro Access Service Ltd Registered in England and Wales CN: 10936237 9 Cannon Street, Wellingborough, United Kingdom, NN8 4DJ